Wire Wiring Harness

Category Archives: 2011-2014

2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom

Posted on by
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom

2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
This main harness is in very good condition and shows normal signs of wear. We have similar items for sale, please check out. Send us a message if you cannot find what you’re looking for. Powered by SixBit’s eCommerce Solution.
2011-2014 Yamaha Stryker Main Engine Wiring Harness Motor Wire Loom
2011_2014_Yamaha_Stryker_Main_Engine_Wiring_Harness_Motor_Wire_Loom_01_xef Tagged: , , , , , , , , , .

2011-2014 Ford 5.0L Coyote Modular EFI wiring harness kit Telorvek design

Posted on by
2011-2014 Ford 5.0L Coyote Modular EFI wiring harness kit Telorvek design

2011-2014 Ford 5.0L Coyote Modular EFI wiring harness kit Telorvek design
Manual and 6R80 automatic transmissions.. Comes with all of the sensor connections pre-installed on color coded and printed wire which attaches to the engine and transmission using the factory ECM plus wiring for the fuel pump, electric fan and diagnostic port. It will allow you to wire the engine and transmission when installing them into a earlier model vehicle like Cobra kit cars, Muscle cars, Street rods, Trucks and 4×4, etc. This is not a factory replacement wiring harness. This harness is designed to use the original Ford 5.0L ECU. (not included with this kit). Will have to be reprogrammed to remove PATS anti-theft at a minimum. The picture represents the items you will get, but some items may be different. These engines originally used a returnless fuel system. The ECM maintained a fuel pump that was equipped to operate at variable speeds. A fuel pump driver and fuel rail pressure transducer worked with the ECM to control this special fuel pump. To use this wiring kit, you will need to use a return fuel system. You will need to install a fuel pressure regulator between the pump and fuel rail and run a return line from that fuel pressure regulator back to the fuel tank. These engines require 32-33 PSI at idle and 41-42 PSI at Wide open throttle. Each item is specific and we want to include the correct wiring. We cannot build the kit until the question has been answered. With this harness you can design where to mount your ECU and the routing of each wire custom to your vehicle. This harness allows you to mount the computer up to 20 feet (in Trunk, under seat, behind kick panel inside the vehicle) away from each sensor. The computer plugs-in 18 inches from the stainless steel Telorvek panel used as a junction between the computer and sensors that contains the fuses, relays and check engine light. There is an additional wire for mounting the check engine light on your dash. You will get a bag for each sensor with a wired sensor connector and 20 feet of wire. Each wire is printed where it is coming from and going to every 10 inches. You plug in each sensor and run the wires back to a terminal block on the Telorvek panel, cutting the excess wire and crimping a fork terminal. Place the numbered wire with terminal under the numbered screw and tighten the screw. Once every sensor and fuel pump is wired and plugged in, you will have 3 wires to hook up (Battery feed, Ignition feed and ground). This harness is built in the U. With brand new OEM Ford connectors and 260 degree automotive grade GXL wire (thicker insulation than TXL wire). The harness includes OEM diagnostic port for Ford 5.0L. The harness can be used with long tube headers or stock exhaust manifolds. It will work with any performance upgrades or engine diagnostic tool designed for the Ford 5.0L engine you are using. These are built right with quality parts from the correct manufacturers and quality checked for performance. The item “2011-2014 Ford 5.0L Coyote Modular EFI wiring harness kit Telorvek design” is in sale since Tuesday, January 24, 2017. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “qualityautospecialties” and is located in Chester, Pennsylvania. This item can be shipped to North, South, or Latin America, all countries in Europe, Japan, Australia, South africa, New Zealand, Egypt, Reunion.
  • California Prop 65 Warning: California’s Proposition 65 requires that a clear and visible warning be provided to consumers in California prior to the purchase of products that have the potential to expose them to various substances which may cause cancer, birth defects or other reproductive harm. Quality Auto Specialties cares about your safety and hopes that you take steps toward protecting yourself. To reduce any potential exposure, we recommend that your hands are cleaned after handling any of our products. Additionally, our wiring products are not suitable for ingestion in any way. For more information, visit www.P65Warnings.ca.gov
  • Country of Manufacture: United States
  • Manufacturer Part Number: CY-11
  • Brand: The Detail Zone
  • Warranty: Yes

2011-2014 Ford 5.0L Coyote Modular EFI wiring harness kit Telorvek design
2011_2014_Ford_5_0L_Coyote_Modular_EFI_wiring_harness_kit_Telorvek_design_01_ivp Tagged: , , , , , , , .