This Wiring Specialties PRO Series harness was designed from the ground-up to exceed OEM specifications for wire quality, power/ground routing. Looking for the best in aesthetics, weight savings and reliability out of your harness? Our Pro Series harness completely replaces your old OEM harness so you can forget about those electrical gremlins. This harness is specifically engineered for. BMW E30 with a NON-VVTi 2JZGTE. It was developed in house on an actual 2JZGTE engine in an s14 chassis to ensure a perfect fit to all engine sensors. With our simplistic and’tucked’ approach the end result will be a clean and worry free installation with a guaranteed start up. Wiring Specialties offers a number of options for common performance upgrades for this product. Build your perfect harness by selecting from the available options to the right a. Nd as always if you have any questions reach out to us. Engine: JZS147 and JZA80. Any non-VVTI 2JZGTE from MKIV Supra. Chassis: RHD JDM S13 180SX/Silvia. Retains factory A/C (optional), speedometer (required converter), tachometer, engine temperature gauge, oil pressure sensor, alternator charge light, reverse lights and wipers. Factory Speedometer, Tachometer, Alternator Warning light, wipers and reverse lights remain functional. Optional Factory Gauge Sensor Adapters retain the factory BMW Oil Pressure and Coolant Temp cluster functionality. The adapters are also machined to support most aftermarket temperature and pressure gauges that require a 1/8-27 thread pitch. Will require the use of E30 BMW (Original BMW sensors) Oil and Temp sensors (1-wire). INCLUDED WITH THIS PRO-SERIES HARNESS. Main Engine and Transmission one-piece tucked harness. 2x knock sensor connections. 4x VSV twin Turbo control connectors (Twin Turbo option only). Boost solenoid wiring (with AEM/Haltech or aftermarket computers). 12-pin and 4-pin igniter chip connectors relocated to inside the. 2x Cam sensor connector. Idle air motor connector. OEM Oxygen sensor connectors (wideband wiring is not part of the EFI harness, except AEM Infinity 6/8 or Haltech Elite). 2x ground ring terminals. ECT sensor connector and cluster coolant temp switch connector. Reverse lights sensor connector. OEM oil pressure 1-pin connector. ECU Diagnostics mode connector. No traction Control wiring supplied. Printable install instructions with pictures. Turn Key ENGINE START Guarantee. PRO-SERIES HARNESS TECHNICAL SPECS. Plug and Play installs in minutes. NO CORE HARNESS or additional wiring required. OEM wire colors used, where applicable. All sensor signal connection use EM shielded wires. Fireproof fiberglass sleeving used in high-temp sections near the manifold & turbo (-40°C/-40°F to +450°C/+845°F operating temperature). Point-to-Point continuity tested on every wire. Constructed using exact OEM connectors and seals. Made with high temp TXL wire with adhesive shrink tubing (-40°C/-40°F to +125°C/+257°F operating temperature). Wrapped in lightweight nylon loom (-94°C/-137°F to +125°C/+257°F operating temperature). Fully tested after production for an easy plug-and-play replacement. Type of Return Request. The item “Wiring Specialties Engine Tranny Harness 2JZGTE Non-VVTI into BMW E30 Pro Series” is in sale since Wednesday, December 6, 2017. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Charging & Starting Systems\Other”. The seller is “autocat51″ and is located in West Covina, California. This item can be shipped worldwide.
- Brand: WSP
- Manufacturer Part Number: WRS-PRO2JZ-E30
- California Prop 65 Warning: WARNING: The items in this ebay listing are found to have compounds and chemicals known to the State of California to cause cancer, birth defects, and reproductive harm:
