Wire Wiring Harness

Hello, This listing is for one new 1964 Chevrolet Impala SS Under Dash harness with console shift, manual or automatic transmission with AC. Includes complete fuse box assembly. Harness is New, made in the USA. This has all the connections as follows. Headlight switch, lighter, heater controls, heater blower resistor, light socket for heater controls, ignition and light socket, brake light switch, back up light switch, dimmer switch, neutral safety switch, radio, E-brake warning buzzer, turn signal switch and a few others required for the under dash wiring. Also comes complete with original style BUS fuse box, both half’s. The back half of fuse box has the bulkhead connector for engine and forward light harnesses. Has connections for the under dash cluster harness which is a separate harness from this. Fits: 1964 Impala Super Sport with console/floor shift, manual or automatic transmission and AC. Thanks for visiting and hope to have your business. The item “1964 Chevy Impala SS Under Dash Wiring Harness with Fusebox MT AT withAC” is in sale since Saturday, May 30, 2009. This item is in the category “eBay Motors\Parts & Accessories\Vintage Car & Truck Parts\Other Parts”. The seller is “24kaccents” and is located in Niagara Falls, New York. This item can be shipped worldwide.

• Brand: American Auto Wire
• Manufacturer Part Number: CF30169
• Surface Finish: Wiring Harness
• Warranty: Yes
• Country/Region of Manufacture: United States

Performance Fuel Injection Systems Stand Alone Fuel Injection System WIRE HARNESS & ECM (computer). This is a fuel injection system Wire harness. Upgrading your carburated Classic Car, Truck, Jeep, Mud Bogger, OFF Road Truck, or Hot Rod to Fuel Injection and using a TBI Engine from a Truck Van then Performance Fuel Injection Systems has a harness for your project. Fuel injection is becoming a very popular upgrade. Swaping in a TBI Engine is nothing new. Fuel Injection Wire Harness from Performance Fuel Injection Systems is Just what you need. We eliminate what you don’t need. Our custom Chips in the ECM (computer) have what you don’t need turned off, so you wont get a bad running engine or a CHECK ENGINE LIGHT. Stand alone means that the system only needs 12 volt ignition and 12 volt battery feed to make the system run. We only use the 5 sensors so this is a very simple system, and the best of all the fuel injection system installed on your vehicle runs completely closed loop once warmed up (14.7 air fuel ratio) just like the new vehicles, but with fewer sensors than a new car. The TBI system is based off the reliable 1987 to 1995 Chevy PU with Throttle Body Injection (TBI) this was a proven great system for years and there were and still are thousands of these vehicles out there. The ECM are remanufactured. The wiring harness is all made with TXL wire which is water oil and grease resistance, and all in convoluted loom (split loom) which makes for a good looking system when you open the hood. Comes With Complete Instructions for installation. THIS HARNESS IS FOR A CHEVY TBI ENGINE SWAP. Fuel Injection System Harness includes. Wiring Harness W/fuel pump relay and main power Relay. ECM (maybe re-manufactured) with custom calibrated EPROM chip (installed in ECM). PFI STICKER FOR YOUR WINDOW, FENDER, UNDER YOUR HOOD, OR TOOL BOX. Lifetime on harness against defects 90 days for ECM. The item “TBI Harness WithECM Fuel Injection Wire Harness SBC TBI ENGINE SWAP” is in sale since Tuesday, November 17, 2015. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “performancefuelinjectionsystems” and is located in Elsie, Michigan. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.

• Brand: Performance Fuel Injection Systems
• Manufacturer Part Number: WH0001
• Warranty: Yes
• Country/Region of Manufacture: United States

Performance Fuel Injection Systems Stand Alone Fuel Injection System WIRE HARNESS & ECM (computer). This is a fuel injection system Wire harness. Upgrading your carburated Classic Car, Truck, Jeep, Mud Bogger, OFF Road Truck, or Hot Rod to Fuel Injection and using a TBI Engine from a Truck Van then Performance Fuel Injection Systems has a harness for your project. Fuel injection is becoming a very popular upgrade. Swaping in a TBI Engine is nothing new. Fuel Injection Wire Harness from Performance Fuel Injection Systems is Just what you need. We eliminate what you don’t need. Our custom Chips in the ECM (computer) have what you don’t need turned off, so you wont get a bad running engine or a CHECK ENGINE LIGHT. Stand alone means that the system only needs 12 volt ignition and 12 volt battery feed to make the system run. We only use the 5 sensors so this is a very simple system, and the best of all the fuel injection system installed on your vehicle runs completely closed loop once warmed up (14.7 air fuel ratio) just like the new vehicles, but with fewer sensors than a new car. The TBI system is based off the reliable 1987 to 1995 Chevy PU with Throttle Body Injection (TBI) this was a proven great system for years and there were and still are thousands of these vehicles out there. The ECM are remanufactured. The wiring harness is all made with TXL wire which is water oil and grease resistance, and all in convoluted loom (split loom) which makes for a good looking system when you open the hood. Comes With Complete Instructions for installation. THIS HARNESS IS FOR A CHEVY TBI ENGINE SWAP. Fuel Injection System Harness includes. Wiring Harness W/fuel pump relay and main power Relay. ECM (maybe re-manufactured) with custom calibrated EPROM chip (installed in ECM). PFI STICKER FOR YOUR WINDOW, FENDER, UNDER YOUR HOOD, OR TOOL BOX. Lifetime on harness against defects 90 days for ECM. The item “TBI Wiring Harness WithECM Fuel Injection Wire Harness SBC TBI ENGINE SWAP” is in sale since Tuesday, March 28, 2017. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “performancefuelinjectionsystems” and is located in Elsie, Michigan. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.

• Brand: Performance Fuel Injection Systems
• Manufacturer Part Number: WH0002
• Warranty: Yes
• Country/Region of Manufacture: United States

E171 – LS1, LS2, LS3, L92 LS7 wiring harness. Custom stand alone open loop only Engine wiring harness. 2 Main trunk options 50 or 16 inches long from rear of engine to PCM connectors (allowing easy installation). 3 wire hook up with 1 fuel pump wire and tack. Choice of 3 injector harness leads (Specify Injector Plug). This kit is designed to upfit any GM LS series engine with 24x crank front or rear cam sensor (specify upon order). For 58X go to E172 listing 200518132935. The item “E171 LS1, LS2, LS3, L92 LS7 24X 4L60E wiring harness” is in sale since Monday, March 01, 2010. This item is in the category “eBay Motors\Parts & Accessories\Performance & Racing Parts\Auto Performance Parts\Engine & Components\Other”. The seller is “jas4120″ and is located in Springfield, Minnesota. This item can be shipped worldwide.

• Manufacturer Part Number: sch9907
• Warranty: Yes
• Part Brand: Schwanke Engines
• Country of Manufacture: United States

Ask for a promo code before purchasing. VETTE LIGHTS 3.0 BY CATHEADLIGHTS. Designed, engineered, and manufactured by Catheadlights. The 2nd easiest kit to install on the market… Behind our plug and play kits! 69-71 Lincoln Mark III. VETTE LIGHTS 3.0 by CATHEADLIGHTS. 68-82 C3 Corvette headlight motor conversion kits. Electric headlight opener conversion kit for 68-82 C3 Corvettes designed by Catheadlights. The kit consists of new, Catheadlights exclusive design, CNC laser cut mounts that bolt to the factory vacuum actuator position, no drilling required, complete with refurbished Ford or Mazda motors that have been tapped and use button head bolts to secure them to the mount. No unreliable motors to replace or expensive electronics. The kit is complete and ready to bolt in using GM style black fender bolts with washers and works with Air Conditioned and NON-Air Conditioned cars. The mounts require a small notch to be cut, as shown in the pics, but the Catheadlights mount completely covers it, making installation look factory, and also strengthening the headlight system. The kit comes completely put together, once you make the cut, bolt in the kit, attach and simply adjust the CUSTOM aluminum arms(work like a turn buckle) and the springs, you are ready to plug in the. Included is a simple Bosche style relay wiring harness, the harness is a three wire connection. Power, ground and trigger wire. This wiring harness is recommended for floor mounted dimmer switch Vettes only(68-76), because of the difficulty to connect the trigger wire on column mounted dimmer switch Vettes(77-82). Using the dimmer switch ensures a factory opening look. Other wiring options do not allow your headlights to stay closed while your running lights are on. Detailed instructions are included. New(NOS) motor kits. Kits without motors are also available. As seen on Stacey Davids GEARZ 67 Cougar Interceptor (MAV TV). Featured in Legendary Cougar Magazine. Here are few videos of the kit in action. The item “C3 Corvette 68-82 Electric headlight motor conversion kit / 3 wire harness” is in sale since Friday, March 06, 2015. This item is in the category “eBay Motors\Parts & Accessories\Vintage Car & Truck Parts\Exterior\Grilles”. The seller is “catheadlights” and is located in Clarksville, Tennessee. This item can be shipped worldwide.

America’s Oldest Speed Shop®. Has connections for both the 4L60E and manual 6-speed transmissions. ECM programming will need to match transmission style. Common aftermarket fuel pump and fan relays are included. These harnesses feature all of the connection points necessary to run the engine and transmission if applicable. The emission equipment has been eliminated and only the needed connections to run the engine and transmission are incorporated. ECM programming will need to be done to remove all of the unneeded trouble codes that may be active from the stock application. Programming will need to be done to remove VATS (vehicle anti-theft system) programming, otherwise the engine will not run. These wiring harnesses do not include any type of VATS module to defeat the theft system. Standard length harnesses are 54 from the back of the engine to the PCM connectors. Take the fear out of electronic fuel injection! These engine wiring harnesses are designed to make your engine transplant effortless. Each new harness contains in-depth application-specific instruction sheets, clearly marked factory GM connectors, labeled GXL jacketed wire, GM color coding, and pre-fitted corrugated slit loom for an extra value and professional look. All un-needed emissions wiring is eliminated to make the install as simple and reliable as possible. Made from premium grade GXL jacketed automotive wire. Most wiring is larger gauge than stock application for durability. No splices to reduce points of failure. All primary grounding is done at the head or block and grounding points are isolated from each other to reduce electrical interference and minimize ground looping. Harness wiring matches GM wiring configuration and jacket colors follow GM color coding for easy identification. All electrical connectors are made by Delphi or Packard and are direct fit for GM cars and trucks. Can be installed to run engine in 20 minutes, but figure 4-6 hours for a professional installation. OBD2 diagnostic port for connection to scanners and tuning tools. Made in the USA. By Rich on May 14, 2017. I used it on my 88 camaro lt1 swap it made tucking the ecu away easy and everything work nice. Of all of the wiring harnesses out there….. By Davis racing on May 10, 2017. The speedway harness had connectors that I had not seen on the other harnesses that I have used. The oil pressure and oil level sensor connectors was nice. Fitment was top notch and it was well labeled. Easy To Set Up. Yes, I recommend this product. Related Items / Suggested Parts. Speedway 1985-89 Tuned Port Mass Air Engine Harness. Speedway GM Engine Wiring Harness, 1999-02 LS1. Please pay for all items at the same time. We cannot combine your order if you have already paid. Speedway Motors is Americas Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 65 years. Repack the item in a sturdy box, include a copy of your invoice and complete the form on the back of the invoice. All exchanges need to have reshipping charges included. Speedway accepts full responsibility for the accuracy of our listings and product representation. The item “Speedway 1994-1997 Chevy Pontiac GM LT1 350 5.7L Engine Swap Wiring Harness” is in sale since Wednesday, April 08, 2015. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “speedway_motors” and is located in Lincoln, Nebraska. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.

• Brand: Speedway
• Manufacturer Part Number: 91009497

I hand fabricate most wiring harnesses with any necessary interface required to fit your aircraft needs. All of my wiring equipment is aviation grade mil spec, wires are professionally fabricated and tested before and installations. All wiring harnesses are handmade to perfection… GTN750 Call for price. GTN650 Call for price. The item “Prefabricated Avionics wiring harnesses Gma340 audio panel harness only” is in sale since Friday, June 05, 2015. This item is in the category “eBay Motors\Parts & Accessories\Aviation Parts & Accessories\Avionics\Other Avionics”. The seller is “camp-rodol” and is located in Miami, Florida. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Croatia, Brazil, Chile, Colombia, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Malaysia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.

• Brand: Garmin
• Manufacturer Part Number: prefabricated wiring harnesses
• Warranty: Yes
• Compatible Make: Avionics
• Compatible Model: Gma340,gns430,gtn650,gtn750,gtx327,gtx330
• Country/Region of Manufacture: United States

6.0L Diesel Engine Wire Harness & Sensors is a direct fit for the following. 2004 Ford F-250 Super Duty 2004 Ford F-350 Super Duty 2004 Ford F-450 Super Duty 2004 Ford F-550 Super Duty -With Build Dates After 9/23/2003 Without Fuel Heater. Genuine Ford Part Number: 4C3Z-12B637-CA. The item “04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM” is in sale since Wednesday, December 02, 2015. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Engines & Components\Other”. The seller is “quirkparts” and is located in Quincy, Massachusetts. This item can be shipped worldwide.

• Brand: Ford
• Manufacturer Part Number: 4C3Z-12B637-CA
• Other Part Number: 4C3Z12B637CA
• Placement on Vehicle: Front
• Surface Finish: Wiring Harness
• Warranty: 2 Year
• Product Notes: With 6.0L Engines / Without Fuel Heater
• Primary Color: Black
• Model: F-250 F-350 F-450 F-550 Super Duty Excursion
• Year: 2004 2005
• Make: Ford

Manufactured in the USA by American Auto Wire. This wiring harness kit has everything to wire your car front to rear. Most complete wiring harness kit on the market. Here are some details about the Classic Update Wiring Harness Kit. Replacement headlight switch with internal 30amp circuit breaker included. Retention collar nut, adjustable length shaft, and custom knob are also included. Standard turn signal flasher, hazard flasher mounted on fuse panel, and horn relay mounted on harness. Fuse box designed to fit in original location. All required hardware supplied. New ATO fuse panel allows for easy fuse and circuit breaker accessibility. Harness is laid out and formed to allow for nearly all after market accessories such as; gauge packages, wiper systems, heat and air conditioning systems, etc. Original switch connector bodies! (Exclusive to American Autowire). Along with wiring for your original dome/interior lighting we have included separate under dash light sockets. Instrument Cluster wiring is designed with a cluster harness disconnect system for easy service and assembly. All original terminals, connectors (exclusively from American Autowire), and light sockets are also supplied for original cluster gauges. However, the best aspect of the disconnect system is that any gauge cluster package can be easily and neatly wired in. This includes AUTOMETER, CLASSIC INSTRUMENTS, DAKOTA DIGITAL, STEWART WARNER, and VDO just to name a few. Rear body harness assembly is designed to plug into the main harness in the original location. Flexibility in harness design allows for original or custom routing. Rear body wiring includes backup light lead wires with correct light sockets, stop and tail light lead wires with correct light sockets, license plate lead wires, and fuel tank sender wire and connection. In addition, a complete preassembled trunk lid harness is also included at no extra charge! New floor dimmer switch is provided. Wire length and connection accommodate original floor mount dimmer switch. GM bulkhead connectors for the engine and front light wiring are included and ready for easy installation. Original or custom routing of the new harness is no problem! Engine wiring includes connectors for original points type as well as H. Power and tach connectors supplied for GM H. Alternator connectors are supplied for GM SI series internally regulated alternators. GM CS series alternator adapter is available separately. Front lighting includes extra long leads for special routing when custom under hood appearance is desired. All headlight, park light and directional light connectors and terminals are provided, as well as a switched trigger wire for electric fan relay (usually recommended with AC). You will find that with our inclusion all the original style light sockets, connectors, terminals, etc. Packed into every aspect of this harness, it makes it the most complete system of its type in the industry! Color schematics and easy to understand installation instructions included. Be sure to add me to your favorites list! Thanks for visiting and hope to have your business. The free listing tool. The item “1961 1962 1963 1964 Impala Belair Biscayne Wiring Harness Classic Update Kit” is in sale since Thursday, October 18, 2012. This item is in the category “eBay Motors\Parts & Accessories\Vintage Car & Truck Parts\Other Parts”. The seller is “24kaccents” and is located in Niagara Falls, New York. This item can be shipped worldwide.

• Surface Finish: Wiring Harness
• Manufacturer Part Number: 510063
• Brand: AAW
• Warranty: 1 Year
• Country/Region of Manufacture: United States