Our Pro-Series is ideal for those looking for the best aesthetics, weight savings and reliability. Completely replace your old harness and forget about electrical gremlins. Dress up your bay and take all the pain out of wiring work with this harness. This Wiring Specialties PRO Series harness was designed from the ground-up, specifically for a Universal installation with a 1JZGTE VVTI engine swap. It was developed in house on an actual JDM JZ engine to ensure a perfect fit to all engine sensors. This harness will work exceptionally well in any installation chassis. Anything from a Dune buggy to a Classic car or a race car. The engine fires up with only 2 wires needing connection, along with a fuel line and a good battery. The harness is designed’Tucked’ for a clean installation. The harnesses are built to exceed OEM spec for wire quality and power/ground routing. Wiring Specialties offers a number of options for common performance upgrades for this product. Build your perfect harness by selecting from the available options to the right. Engine: JZZ30 and JZX100 1JZGTE VVTi. Any VVTI 1JZGTE from Chaser/Mark II. Any VVTI 1JZGTE from Soarer/Crown. Sports cars with no OEM body wiring or Non EFI cars. Cars that benefit from EFI wiring run without body wiring connections. 1JZ VVTi Specific Details. Oval alternator connector supplied, unless requested otherwise. New Style Starter, Plastic coolant and Oil pressure connector supplied be default. Standard – batched ignition (chip and coils) is supplied, but sequential NON VVTi is available as an option. External and removable Fuse and Relay block. Relay system installed for proper ECCS ON and OFF operation with ECU Memory retention. Relay block includes the Ignition, Fuel Pump and Fan relays. The Fan relay can be reclaimed as the AC relay. Fuel Pump output wire that connects directly to the pump. Starter trigger wire available in the interior for easy and clean install. Battery power pick-up at the starter for easy and clean install. Ignition input signal from ignition key. Harness is designed to keep the ECU in the cabin and will reach both left and right bulkhead openings. For GM/LQ9 coils upgrade should be used with an aftermarket ECU and run sequentially. Wideband option for ECUs that do not process a raw wideband signal, a controller must be used. Controller like a EUGO or the Haltech CAN wideband. AEM Infinity and ECU Masters ECUs (and other standalone ECUs) are wired for wideband control direct out of the ECU. The LSU 4.2 Version of the Wideband SHOULD be used, as per AEM. AEM Infinity and ECU Masters are pre-wired for Oil Pressure, Fuel pressure, Oil Temp, IAT and MAP sensor wiring directly to the ECU. ApexI PFC conversions ONLY include the IAT sensor on the main harness. The MAP sensor is wired separately, from the PFC box directly to the sensor. OUTPUT connections for ECU tachometer signal, check engine light, engine temp (Nissan dash signal) and alternator charge indicator, reverse lights, speed sensor, NOTE: Output signals supplied ONLY they may need to be conditioned for use with vehicles gauges. Aftermarket gauges may be required. This part of the install REQUIRES connections of the EFI harness to the body/dash/steering column of the car. User must have basic electrical skills to complete this. INCLUDED WITH THIS PRO-SERIES HARNESS. Main Engine and Transmission one-piece tucked harness. 3x VVTi Coilpack connections. 2x knock sensor connections. Boost solenoid wiring (with AEM/Haltech or aftermarket computers). 10-pin igniter chip connector (relocated to inside the car). 2x Cam sensor connector. Idle air motor connector. OEM Oxygen sensor connectors (wideband wiring is not part of the EFI harness, except AEM Infinity 6/8 or ECU Masters or other). 2x ground ring terminals. ECT sensor connector and cluster coolant temp switch connector. Reverse lights sensor connector. OEM oil pressure 1-pin connector. Speed and Tach signal converter connector. ECU Diagnostics mode connector. No traction Control wiring supplied. Printable install instructions with pictures. Turn Key ENGINE START Guarantee. Tech support for our customers 7 days a week. PRO-SERIES HARNESS TECHNICAL SPECS. Plug and Play installs in minutes. NO CORE HARNESS or additional wiring required. OEM wire colors used, where applicable. All sensor signal connection use EM shielded wires. Fireproof fiberglass sleeving used in high-temp sections near the manifold & turbo (-40°C/-40°F to +450°C/+845°F operating temperature). Point-to-Point continuity tested on every wire. Constructed using exact OEM connectors and seals. Made with high temp TXL wire with adhesive shrink tubing (-40°C/-40°F to +125°C/+257°F operating temperature). Wrapped in lightweight nylon loom (-94°C/-137°F to +125°C/+257°F operating temperature). Fully tested after production for an easy plug-and-play replacement. Note: ETCSi Model also available upon request at additional cost. Type of Return Request. The item “Wiring Specialties Engine Tranny Combo Harness 1JZGTE VVTI Universal” is in sale since Friday, June 24, 2016. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Charging & Starting Systems\Other”. The seller is “autocat51″ and is located in West Covina, California. This item can be shipped worldwide.
- California Prop 65 Warning: WARNING: The items in this ebay listing are found to have compounds and chemicals known to the State of California to cause cancer, birth defects, and reproductive harm:
- Manufacturer Part Number: WRS-PRO1JZVVTI-UNI
- Brand: WSP
