Wire Wiring Harness

ANY ORDERS PLACED AFTER 20:30 APRIL 30th WONT BE DISPATCHED UNTIL TUESDAY 5th MAY. Hand wired Gibson SG harness perfect to upgrade an Epiphone or similar. Using CTS 500k audio taper potentiometers. Sprague orange drop 0.022uf capacitors. Switchcraft 1/4 inch jack socket. Standard 3 way toggle switch. All wired to 50’s wiring this is the must have combination for any les Paul guitar. 50’s wiring is often considered the best option for a Double humbucker guitars because it preserves clarity and dynamics as you roll the volume down. In this wiring scheme, the tone control is connected to the output of the volume pot rather than the input, which means high frequencies are retained instead of being bled off. As a result, the guitar stays brighter and more articulate at lower volume settings, with less muddiness and more usable sweep on the controls. This makes it especially effective for players who rely on the volume knob for cleanup and expressive control-one of the reasons it became a hallmark of vintage Gibson Les Paul tones. We also do more affordable versions of this harness using different brands of parts which we have tried and tested in our own guitars.

Our Signature Hand wired Gibson Les Paul harness perfect to upgrade an Epiphone or similar. This is the holy grail vintage spec for your Les Paul! Using CTS 500k audio taper potentiometers. Medium length brass shaft – imperial. Centralabs bumblebee paper in oil 0.022uf capacitors. Switchcraft 3 way toggle switch. Switchcraft 11TWN Jack socket. Gavitt vintage braided wire. Wired to 50’s wiring this is the must have combination for any les Paul guitar. 50’s wiring is often considered the best option for a Les Paul-style guitar because it preserves clarity and dynamics as you roll the volume down. In this wiring scheme, the tone control is connected to the output of the volume pot rather than the input, which means high frequencies are retained instead of being bled off. As a result, the guitar stays brighter and more articulate at lower volume settings, with less muddiness and more usable sweep on the controls. This makes it especially effective for players who rely on the volume knob for cleanup and expressive control-one of the reasons it became a hallmark of vintage Gibson Les Paul tones. The Centralab Bumblebee 0.022µF Oil Capacitor is a vintage-style guitar tone capacitor designed to replicate the classic “Bumblebee” components found in 1950s electric guitars. It uses an oil-filled, non-inductive mylar construction, which helps deliver a smooth, gradual roll-off of high frequencies when adjusting the tone control. With a capacitance of 0.022µF (22nF)-a common value for humbucker-equipped guitars-it strikes a balance between warmth and clarity, preventing the tone from becoming overly dark while still allowing rich, vintage-style treble reduction. These capacitors are popular among guitarists and builders seeking consistent performance with a classic tonal character, combining modern reliability with the feel and response of traditional oil caps. Vintage-Inspired Sound – Ideal for Les Paul®, SG®, and other classic-style builds.

Hand wired Gibson SG harness perfect to upgrade an Epiphone or similar. Using CTS 500k audio taper potentiometers. Sprague orange drop 0.022uf capacitors. Switchcraft 1/4 inch jack socket. Standard 3 way toggle switch. All wired to 50’s wiring this is the must have combination for any les Paul guitar. 50’s wiring is often considered the best option for a Double humbucker guitars because it preserves clarity and dynamics as you roll the volume down. In this wiring scheme, the tone control is connected to the output of the volume pot rather than the input, which means high frequencies are retained instead of being bled off. As a result, the guitar stays brighter and more articulate at lower volume settings, with less muddiness and more usable sweep on the controls. This makes it especially effective for players who rely on the volume knob for cleanup and expressive control-one of the reasons it became a hallmark of vintage Gibson Les Paul tones. We also do more affordable versions of this harness using different brands of parts which we have tried and tested in our own guitars.

Bloodstone Guitar Works specialise in custom building a guitar to your specification, one that you can have the ultimate confidence in its feel, tone and playability and truly cherish. We also produce our own range of Handwound pickups and Handwired wiring looms and undertake upgrades, repairs and setups. Ready Built up Gibson 3 Pot Flying V etc. Wiring upgrade / Loom. Choose from’58 layout (3 pots in line) or’67 layout (3 pots in triangle). These wiring looms are Individually hand-wired from UK-sourced genuine parts using 22 gauge Gavitt vintage cloth covered wire. A drop in replacement and a great performance and reliability upgrade for all Les Pauls. Top quality matched components are used throughout and the “float wire” method is adopted where all wires are pulled tight and elevated so they make no contact with the control /baseplate. It takes a little longer to build but is definitely worth the effort to maximise performance. Matched CTS USA Custom Audio Taper 500K volume (2) and 250K tone Split Shaft Volume & Tone Potentiometers – smooth linear volume and tone change (no bunching or on/off effect) – 500K and 250K pots are what GIbson fit – please ask if you require an alternative. 0.022uF Sprague “Orange Drop” Tone Capacitor – removes the thinness and harshness inherent with budget capacitors. Separate “treble bleed” mod for both pickups – no muddiness of tone when reducing the volume knob. Premium quality Gibson USA (SwitchCraft) / Epiphone equivalent High quality import and No Switch option. Bridge earth wire supplied with heatshrink tube to twist join with exiting earth, solder and insulate. Easy to follow colour coded wiring diagram. PLEASE ASK IF YOU REQUIRE A SOLDERLESS VERSION, ALTERNATIVE POT VALUE, SOLID SHAFT POTS, Etc – THIS CAN USUALLY BE ACCOMMODATED FROM STOCK AT NO ADDITIONAL COST. Fully soldered together and includes all nuts screws and washers ready to fit to your guitar. Atched in-house to within 10 Ohms (CTS pots tolerance can be +/- 20% so a 250K pot can vary from 220-300+ Ohms). Now using the 715p version which is sonically superior to the commonly used 225p. Customer Service Enquiries and m. Ore details, including custom guitars and builds available at: bloodstoneguitarworks.

Upgrade or replacement wiring harness for a Gibson Flying V (or style) electric guitar. Volume, Volume, Tone, 3 Way Toggle Switch, and Input Jack – USA Spec. Our custom harnesses are made to the absolute highest of standards, meticulously inspected, and sent out ready for installation. Built with the quality of workmanship you would expect from 10+ years experience, and 1000’s of harnesses wired. Using only professional grade components and materials. Giving you confidence in both the longevity, and most importantly, the performance of these parts. We deliberately leave an extra amount of length between wired connections. Ensuring that the harness will fit correctly, and that the components and connections will not break from being overly tight. (Please contact first if you are unsure of what you require in regard to component size etc). Switchcraft USA – 1/4 Mono Input Jack. THE industry standard for input jacks with a long and proven track record. EVERY time you plug in your lead you will know it has the strength and reliability to hold. Most importantly it will not fail on you with frustrating crackles and loss of signal. Right Angle, 3 way, Toggle Switch – Realtone. Heavy duty and reliable Right Angle Toggle Switch, 8mm thread length, 12mm diameter, chrome finish. 022 mfd Orange Drop Tone Capacitor. Sprague Capacitors have a well renowned, 50+ years, reputation for reliability, stability, and consistency in tone with no microphonics. They are a polypropylene and aluminium foil capacitor with orange flame retardant epoxy shell. CTS USA 500k Precision Volume and Tone Pots – Split Shaft. These are the best quality pots available. The precision audio taper gives you a smoother and more accurate response, with a. Brass shaft and tighter resistance tolerance. USA spec 9.5mm diameter and 12.5mm length brass threaded collar (Total length of the shaft to the top of the spline is 22.2mm), 24 spline (fine) brass split shaft 6mm, 24mm Pot casing diameter. 1 x Nut, 1 x Lock Washer, 1 x Dress Washer. 0.001 mfd Capacitor +. 120k 1/4 watt resistor wired in parallel. A “Treble Bleed” circuit is added to the volume pot/s to improve taper and remove the unbalanced roll off. This keeps your clean tones clean and the high end frequencies consistent when turning the volume up and down through 1-10. This is the perfect simple upgrade if you use manual volume swell as an effect. Or if you are using your guitar volume pot to react with and against overdrive, distortion, or fuzz effect pedals. Quality thick, 22 Gauge, cotton braided, wax insulated, vintage style, pull back wire used between components. IMPORTANT POINTS TO NOTE. Switches – Do not include tips (unless otherwise described). Pots – Do not include knobs (unless otherwise described). A separate earth wire (generally runs under a bridge) is not included, but can be if you request/message us. Listing photos are stock photos for advertising. The harness you receive will have the exact top of line parts as per photos/description. The workmanship will be of the same highest quality with all parts thoroughly tested. The majority of all components are US (imperial) measurement parts. CTS pots require a 3/8 hole diameter. For metric /import/Asian made guitars and basses you will generally need to widen mounting holes. Import/metric knobs and switch tips will/may not fit correctly and will possibly need to be replaced. Depending on the thickness of control plates or body cavities you may need to add an extra washer or two on the inside of the pot thread to lower the overall height of the pot knob. The harness will be delivered fully soldered, including switches and jacks. To run through body cavities, jacks and switches may/will need to be de-soldered and re-soldered. All harnesses are wired in a “modern” style. Otherwise, your harness will be posted within 24hrs (on average) and it will be too late to make changes. We are ALWAYS available to help if you get stuck. Harnesses are always tested and are 100% correct and without fault. Generally, if you experience a problem when installing it will be due to a short/earthing/backwards soldering issue. We can talk you through the correct wiring! Guitars and Basses are packed on Monday (courier collection Tuesday) and Thursday (for courier collection Friday). We take great care and pride in making sure guitars are carefully set up and packed correctly for transport, so we do not rush this step. The String Switch Noise store operates primarily as an online business. However, we do have a dedicated showroom 30min south of the Brisbane CBD. However, there are some restrictions with regions and package size. Any questions you may have about this should be directed to your local countries authorities. However please allow up to 72hrs for packing and courier pickups. Small items such as effect pedals and wiring harnesses are sent via Australia Post standard service, with tracking ONLY. Both domestically and internationally. No responsibility will be taken from us for the loss or damage of an item by Australia Post. Courier deliveries can NOT be sent to a PO Box, Parcel Locker, or Parcel Collect service. They must be sent to a physical address, where someone can sign for the item on arrival. All items are packed to the highest degree for transit. Proudly, our packaging is at the highest of standards, with the best reputation you will find anywhere in the industry. This comes from 2500+ guitars (and counting) being sent without issue both Australia wide and internationally over 8+ years (and counting). A great amount of pride and detail goes into making sure every item arrives safe and in a timely manner. Guitars, pending the instrument, have strings de tuned so there is no tension on the neck and headstock. Neck/body /headstock are wrapped separately in multiple bubble wrap layers, high density foam and/or cardboard reinforced. If applicable it is then placed in gig/soft case or hard case. If in gig/soft case it is once again bubble wrapped/foam reinforced before being boxed. All voids are padded out and the body edge, base, and top of head stock foam reinforced/padded. Finally, the boxing will have copious amounts of high visibility “Fragile” and “This way up” warning labels. We are also extremely environmentally conscious. We re use and recycle almost all bubble wrap, foam, and cardboard packaging materials. The are no holds, deposits, or layby. We NEVER use stock photos. An extensive amount of time and effort is put in to accurately show the items true condition, colour, and shape. Though please realise the limitations of photography. Images and colours can be perceived differently depending of the type and quality of the device it is viewed on. Advertised photos form a large part of the representation of the items condition. Please view the photos carefully as well as reading all item descriptions and/or condition text. Whilst every effort is made to photograph all parts of items, not every little dimple/micro scratch can or will be photographed. We always photograph any and all large cosmetic flaws, such as paint chips/cracks/large dents, that we consider to be significant. Cosmetically, items are as per detailed photos and/or descriptions. Functionally, all pots, jacks, switch and machinery components are working without issue, and serviced upon arrival. Each item is tested and/or serviced/set up before listing. Guitars and basses are set up with action at a standard with no playability issues, unless otherwise described. However please understand no one set-up is right for everybody. If you prefer a different action height/tuning/string gauge please adjust at your own liking. Please also realise that almost all items are used, and most are 20-30+ year vintage instruments/effects. They will exhibit some wear and tear. If you need detailed specifics, extra information/on the bench specs can be given about anything you require. Please do not hesitate to ask if this is necessary. However, we are always happy to help and work through any issue, in the rare event that one arises.

Gibson Les Paul Wiring Harness PCB, This Item is Solderless. 4 x 500k CTS potentiometers. Tomo Systems – Les Paul PCB. 2x 0.022uf Orange Drop Capacitors. See my other listings for other configurations. If you also wish for a customisation, drop me a message and we can open a dialogue to work something out as I’m always looking to add to the line.

Gibson Les Paul Wiring Harness PCB, This Item is Solderless. 4 x 500k CTS potentiometers. Tomo Systems – Les Paul PCB. 2x 0.022uf Orange Drop Capacitors. See my other listings for other configurations. If you also wish for a customisation, drop me a message and we can open a dialogue to work something out as I’m always looking to add to the line.

Bloodstone Guitar Works specialise in custom building a guitar to your specification, one that you can have the ultimate confidence in its feel, tone and playability and truly cherish. We also produce our own range of Handwound pickups and Handwired wiring looms and undertake upgrades, repairs and setups. LONG SHAFT Ready Built up Gibson Les Paul Wiring upgrade / Wiring Loom. Long Shaft Length (18mm thread) – See other listing for cheaper 10mm option. These wiring looms are Individually hand-wired from UK-sourced genuine parts using 22 gauge Gavitt vintage cloth covered wire. A drop in replacement and a great performance and reliability upgrade for all Les Pauls. Top quality matched components are used throughout and the “float wire” method is adopted where all wires are pulled tight and elevated so they make no contact with the control /baseplate. It takes a little longer to build but is definitely worth the effort to maximise performance. Matched CTS USA Custom Audio EVERSE Taper 500K or 250K (You choose) Split Shaft Volume & Tone Potentiometers – smooth linear volume and tone change (no bunching or on/off effect). 0.022uF Sprague “Orange Drop” Tone Capacitors – removes the thinness and harshness inherent with budget capacitors. Separate “treble bleed” mod for both pickups – no muddiness of tone when reducing the volume knob. Premium quality SwitchCraft / High quality import and No Switch option. Bridge earth wire supplied with heatshrink tube to twist join with exiting earth, solder and insulate. Easy to follow colour coded wiring diagram. Fully soldered together and includes all nuts screws and washers ready to fit to your guitar. Atched in-house to within 10 Ohms (CTS pots tolerance is +/- 20% so a 250K pot can vary from 200-300 Ohms). Now using the 715p version which is sonically superior to the commonly used 225p. This item is in the category “Musical Instruments & DJ Equipment\Guitars & Basses\Parts & Accessories\Guitar & Bass Parts\Knobs, Jacks & Switches”. The seller is “bloodstoneguitarworks” and is located in this country: GB. This item can be shipped to United Kingdom, Austria, Belgium, Bulgaria, Republic of Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Bahrain, Canada, Japan, New Zealand, China, Israel, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Bangladesh, Bermuda, Brunei Darussalam, Egypt, Guernsey, Gibraltar, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Sri Lanka, Macau, Monaco, Maldives, Oman, Pakistan, Reunion, Saudi Arabia, South Africa, United Arab Emirates, Kuwait, Philippines, Qatar, Vietnam.

• Jack socket type: Switchcraft 3/8\
• Switch type: SwitchCraft Switch Fitted
• To Fit: Electric Guitar
• Country/Region of Manufacture: United Kingdom
• Brand: Gibson
• Type: Loom

920D Custom Shop Les Paul Black Beauty pre-wired upgrade harness with Orange Drop. A very economical way to improve the tone of your LP! Direct replacement for your vintage or Historic Les Paul 1959 1958 1960 reissue (R0, R9, R8, R7). Hear what you’ve been missing from your humbuckers! Kit includes: 3 CTS 500K (+/- 10% tolerance) knurled long shaft audio taper potentiometers (2 volume, 1 tone) 1 Bourns 500K Push / Pull tone pot. 2 Orange Drop capacitors. Also, CTS pots require a 3/8 hole (in the top of your guitar); most USA made guitars are drilled this way, however imported guitars often are not. Sigler Music Center has been in business for over 50 years. Sigler Music Center 1191 Sturgis Rd Conway, AR 72034. Accessories, software and manuals MUST be included. Pack your return securely and insure it. We do our very best to help customers when they request to return an item. Customer service is our first and foremost concern. However, there are a few items that are non-returnable. Although unlikely, on occasion an item gets damaged while in transit. Usually when a box shows some wear and tear, the product inside is in perfect condition. Please be sure to inspect the contents. If you receive a product that you believe is defective, message Sigler Music immediately to speak with a product specialist. If necessary, a return authorization will be provided. Please Note: Oversize items need to be repaired locally whenever possible. A Sigler Music team member can help you find a nearby service center. If your item arrives damaged or does not work, please contact our office immediately. The item “Gibson Les Paul Black Beauty 3 Pickup Wiring Harness Bourns CTS Switchcraft New” is in sale since Tuesday, January 6, 2015. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Parts & Accessories\Guitar & Bass Parts\Knobs, Jacks & Switches”. The seller is “sigler_music” and is located in Conway, Arkansas. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Dominican republic, Panama, Trinidad and tobago, Guatemala, El salvador, Honduras, Jamaica, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay, Russian federation.

• Brand: 920D Custom
• To Fit: Electric Guitar
• Type: Wiring Harness
• MPN: LP3P

THIS IS A REPRODUCTION OF THE VINTAGE WIRING HARNESS FOR LES PAUL WITH REPRO. 022 BLUMBLE BEE CAPACITORS, USING CTS STANDARD SHAFT 500K POTS, CLOTH COVERED WIRES AND SWITCHCRAFT JACK AND 3 WAY SWITCHCRAFT SWITCH. The item “COMPATIBLE WITH GIBSON LES PAUL BUMBLE BEE REPRO VINTAGE WIRING HARNESS & SWITCH” is in sale since Wednesday, December 18, 2019. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Parts & Accessories\Guitar & Bass Parts\Other Guitar & Bass Parts”. The seller is “onlymusic” and is located in Cape Coral, Florida. This item can be shipped worldwide.

• MPN: Does Not Apply
• Country/Region of Manufacture: United States
• To Fit: Electric Guitar
• Model: LES PAUL
• Brand: ONLYMUSIC
• To Fit Guitar: GIBSON LES PAUL
• Type: Wiring Harness